|
|
1969-1997 Nissan Pickup 4WD
Replacement Sleeve - Replacement Sleeve for Air Lift Air Suspension Kits
Air Lift Company has been engineering and assembling air springs
right here in the USA since 1950. Our superior engineering,
designs and materials ensure that we make the best air
bags in the business! Enjoy your vehicle?s
ride loaded or unloaded? air adjustability is the difference!
If towing or hauling is a bouncing, swaying
?thrill ride?? if you?re concerned about safety when your vehicle
is loaded? if you and your passengers could use a
little more comfort in that nice ride of yours? maybe
it?s time to ?add air?! Factory suspensions
must compromise between ride comfort and load hauling capacity. Smooth
ride suspensions can?t carry heavy loads; heavy springs ride rough,
especially when the vehicle is unloaded. Air adjustable springs solve
these problems and give a safe, comfortable ride under all
load and road conditions. Just add air for a muscular
suspension when towing or hauling a heavy load; remove it
for a softer ride when the load is removed.
Air is better than steel! Sure, you
can add steel helper springs to help handle your trailer
or heavy load. The trouble is, if you use an
?extra leaf? steel spring, that ?extra? spring rate is always
there, whether you?re loaded or not! Using a non-contact or
?overload? steel spring sounds better? but it only engages when
your vehicle sags enough to make contact! Does that make
sense? And rough roads will give you sharp ?spikes? of
extra spring rate, in other words, rough ride. Who wants
that? Maybe your Main Passenger doesn?t like that rough ride
and maybe you?d even like a little more comfort when
you?re riding light. Air adjustability is the key!
Air suspension is all we do. You can?t buy
a better air spring! The benefits of
Air Lift air springs: ? Air Lift exclusive! Guaranteed non-corrosive
high-strength reinforced composite Zytel® endplates! ? Air Lift exclusive!
Shur-grip crimp ring, extra-strong steel for long, trouble-free life.
? Your air springs will never come apart! We back
up our bags with a free lifetime air spring replacement
warranty for failures resulting from endplate or crimp failure. If
the spring comes apart, we?ll replace it, no charge, no
hassle. Just contact your dealer or call Air Lift at
(800) 248-0892. ? Bags built with superior reinforced natural
rubber or tough molded polyurethane (see the individual kit descriptions
for details). ? State-of-the-art, easy to connect engineered polymer
air fittings. ? All kits complete with everything you
need: bags, brackets, hardware, air line, installation alignment tools (where
needed), illustrated instruction manual. Put an end
to these common problems: ? Sag: Proper weight distribution
to all the tires improves steering, braking and tire wear.
Especially important when towing; adjust the air springs to accept
the tongue weight of your trailer. ? Sway and
body roll: Air springs increase spring rate and vastly improve
vehicle stability. Less roll and s
$78.00
Mitsubishi Precis Sedan 87;
Rear Panel 1991-1993 BMW M5
Front HP PLus Hawk Brake Pads 2006-2006 Chevrolet Avalanche 6.0L
DiabloSport Predator Hand Held Flash Programmer 2004-2004 Pontiac:
Rear Power Slot Cryo Rotors
Left and Right (Pair)
[More]
|
|
1997-1998 Ford F250 Pickup - 3/4 Ton, Exc. Super Duty
Rear Performance Ceramic Hawk Brake Pads - Performance Ceramic Ultimate
stopping power in an ultra-low dust, low noise ceramic compound!
Hawk Performance has introduced a premium, high performance,
ultra-low dust, low noise compound called Performance Ceramic.
Performance Ceramic is engineered to reduce brake NVH (Noise,
Vibration and Harshness), creating a quieter performing brake pad. Furthermore,
the ceramic brake pad formula has a linear friction profile
that allows your ABS brake system to work more effectively.
With Performance Ceramic you can expect reduced brake pad wear,
lower dust output levels and a rotor-friendly brake pad.
Performance Ceramic ? quiet, clean & fast
stopping! Key Features: ? Increased
stopping power ? Increased rotor life ? Extended
pad life ? Ultra-low dust ? Extremely quiet
? Stable friction output ? Recommended for import
domestic automobiles, luxury SUV?s, sports trucks & vans.
Today?s alloy wheel designs on premium vehicles has
contributed to customer demand for a low dust performance brake
product. Specify Hawk Performance?s Performance Ceramic brake pads for your
luxury car, SUV, or truck. All
Hawk Performance Performance Ceramic brake pads provide a limited lifetime
warranty, ensuring products to be free of defects from manufacturer?s
workmanship and materials. Note: Hawk Performance
burnishes its Performance Ceramic brake pads as a final step
in the factory, but all brake pads have to be
bedded-in with the rotors (new or used) that they will
be used against. Properly bedding-in new brake pads results in
a transfer film being generated at the pad and rotor
interface to maximize brake performance Brake Pad
Installation Procedure 1. Install brake pads properly. Be
sure pads are securely positioned in the caliper.
2. Flush system with fresh brake fluid.
3. Check all hydraulic parts for excess wear and
tear. 4. Check disc for proper thickness,
parallelism, and lateral runout. 5. Check disc
for scoring or grooves over .012?depth. If either applies, resurfacing
is required. 6. If discs do not
need resurfacing, then contamination from the previous brake pads must
be removed. Sand discs with 130 grit sandpaper using moderate
pressure. Use soap and water to clean discs? surface after
sanding and machining. Discs should be free and clear of
oil, grease, and brake fluid. 7. Inspect
calipers for freedom of movement. Lubricate where necessary.
Burnishing Instructions 1. After installing new
brake pads, make 6 to 10 stops from approximately 30-35
mph applying moderate pressure. 2. Make an
additional 2 to 3 hard stops from approximately 40 to
45 mph. 3. DO NOT DRAG BRAKES!
4. Allow 15 minutes for brake system
to cool down. 5. After step 4
your new pads are ready for use.
$76.67
2002 - 2006
Dodge Ram 1500
Dodge Ram 2500
Dodge Ram 3500
Mirror, Electric With Fact. Heat & Front & Rear Face Sig. Conver
[More]
|
|
1973-1987 Chevrolet C10;
McGaughys 1/2 Ton 2wd 1" Rotors, 4/6 Deluxe Drop Kit - As a leader
in the lowering suspension market for over 20 years (since
1984), McGaughys engineering capabilities are endless and continue to release
high quality parts that the public demands. McGaughys produces lowering
suspension parts that haven?t been done before in the world
and they do it right the first time. McGaughys rides
on the reputation for the parts being a bolt on
installation and making sure the entire lowering works hand in
hand with necessary factory components. McGaughys kits are made so
the average guy in his garage can do the installation
without any major modifications. Manufacturer Part Number 93151. Also known
as Part Number 738746DLD.This Kit Includes:2" Front Spindles2" Front Coils6"
Rear Flip KitC-Notch
$800.06
1998-2000 Chrysler Cirrus:
4 Cylinder 2.4L;
MagnaFlow Direct Fit Catalytic Converter
[More]
|
|
|
1997-2001 Honda:
Pro Stop Slotted & Dimpled Rotors
Left and Right (Pair) - Power Slot Premium Replacement Rotors
Streetbeatcustoms.com is proud to present Premium Replacement
Rotors from Power Slot. Excessive heat can cause resins
in your brake pad to vaporize or "outgas." As the
brake pad wears, the used friction material turns into a
fine dust. This boundary layer of heat, gas and dust
builds up between the pad and rotor surfaces and inhibits
performance. Here's where Power Slot's slotted brake rotors make a
big difference. Power Slot's exclusive Vac-U-Slots are
machined into the rotor and help evacuate gasses and dust,
shed heat, and keep the brake pad surface clean. And
in wet, raining conditions, our Vac-U-Slot helps push water off
the braking surface for better stopping power.
The Vac-U-Slot also serves as a visual wear indicator. The
slot is machined to the rotor?s minimum thickness where it
crosses the outside edge. If you cannot see the slot
along the outside edge, the rotor has worn down to
its discard depth. Manufacturer Part Number: 798DSLR Model
Fitment for Brakes and Rotors: 1997-2001 HONDA PRELUDE, 5-LUG
$242.58
MagnaFlow Universal Catalytic Converter, Wide Oval, 6.2L/6000 lbs, 3" Inch Inlet/Outlet, 12" Inch Body, 16" Inch Overall, 7" Inch Wide, Sing 2006-2007 Lincoln MKZ;
3D Carbon Right Side Skirt Acura Integra 1994-2001
Wing / Spoiler Terminatorâ„¢
[More]
|
|
|
1979-1993 Ford Mustang Coupe, Hatchback / 1979-1985 Mercury Capri: Left Side Skirt by Xenon - Xenon body styling kits, sport flares and styling parts
are each individually designed. We provide distinctive automobile accessories that
allow automobile, sport truck and SUV owners an opportunity to
stylize and individualize their vehicles. Products are designed to flow
with the vehicles natural lines and meet, what we believe,
are the popular trends on the cutting edge of automotive
fashion. All Xenon styling kits are offered as individual
parts or as a kit. This means customers can add
individualism to their car, sport truck or SUV.
Fits Ford Mustang 1979, 1980, 1981, 1982, 1983, 1984,
1985, 1986, 1987, 1988, 1989, 1990, 1991, 1992, 1993
Fits Mercury Capri 1979, 1980, 1981, 1982, 1983, 1984,
1985 Fits Models: 1979-1993, Ford Mustang (Coupe,
Hatchback or Convertible) 1979-1985, Mercury Capri
$214.00
Ford Ranger 94-01 All Sales Third Brake Light Cover; Oval Design; Polished
[More]
|
|
|
Iced Out EMZ 22" Series II Chrome Emblem with Clear Crystals, Pair - Introducing Iced Out EMZ, the
leaders in the ultimate custom-made car accessory: "The iced-out emblem."
Designed and hand-crafted to meet your needs, there are
an assortment of styles and colors to suit your ride,
your ideal color scheme, or to simply suit your mood.
Be the highlight at the red carpet, the talk
of the town, the envy of all your friends and
the center of every woman's attention. Make your dreams
into reality with Iced Out EMZ. Each Iced Out
EMZ emblem is embedded with hundreds of Swarovski's most exquisite
crystals. Swarovski's crystals are known for their brilliant diamond
shine without spending the diamond price. All crystals are
strategically placed to create the perfect luminescence and sparkels without
the loss of emblem rigiditiy or strength. Iced Out
EMZ prides itself on high quality and unsurpassed standards by
providing the best adhesive that 3M offers to ensure our
emblems have a long lasting stay on any vechicle surface.
Iced Out EMZ is also offering different exquisite colored
crystals as well as custom designs. As a final
touch, each emblem comes in it's own black alligator skin-embossed
pattern jewelry box with a black sil interior ensuring that
your product will arrive to you in its most pristine
condition. How Big Are You? Series 2 Customize your
ride and let the world know what kind of "Redefined
Baller" you are! Colors available in Crystal Clear.Iced Out
EMZ 22" Series II Chrome Emblem with Clear Crystals, Pair
$99.00
Street Scene Chevrolet Silverado 99-02 Bumper Covers/Valance; Front Bumper Cover/ Valance (Generation 5 Style) 1999 - 2002
Chevrolet Silverado
Fenders/Flares; Complete Fender Flare Set (Box Style) Ford Full Long Bed (8 ft) 73-96, F250/F350 97-98
Saber Tonneau Cover 1993-1997 Nissan Altima
Duraflex Fiberglass Buddy Front Bumper
[More]
|
|
|
MagnaFlow Universal Catalytic Converter, Round Spun-Cat, 5.2L/4500 lbs, 3" Inch Inlet/Outlet, 4" Inch Body, 9" Inch Overall, 4" Inch Wide, C - Details:Universal Catalytic Converter, Round
Spun-Cat, 5.2L/4500Lbs. EPA, 5.0L/4500Lbs. California, 3" Inch Inlet/Outlet, 4" Inch
Body, 9" Inch Overall, 4" Inch Wide, Center-Center
$247.81
Covercraft Block-It 350F Series Fabric - Light Tan (Mini Ext. Cab Trucks (Pickups)) Car Cover; Deluxe long bed - LB w/Cab High Shells(CHS)
[More]
|
|
|
2004-2006 Mercedes Benz SLK-Class, Excluding AMG (R171)
Rear Drilled Gran Turismo Brake Kit
4 Piston Caliper
Disc Size: 328x28
2 Piece Rotor - Brembo Gran Turismo Brake System This line
is dedicated to the most demanding customers.This braking system originates
from the Racing components, consisting of a ventilated, integral or
composite disc, available drilled or slotted, 4, 6 and 8
piston aluminium calipers, a complete set of high performance brake
pads, metal braid tubes and high quality small parts.
Please remember that in the European Community, Gran
Turismo products may only be used in racing and on
private roads, unless you have obtained a new approval in
compliance with directive 98/12/EC. 1. High Performance
Friction Material: Aggressive pads that provide the highest
level of performance. 2. Cross-Drilled or Slotted
Discs: Clears gasses, cleans pads for better ?bite?.
3. Mounting Brackets and Assembly Hardware:
Aircraft quality included and pre-torqued specifications.
4. Stainless Steel Braided Brake Line: DOT/TÃœV approved.
5. ?Floating? Disc Mounting System with Billet
Aluminium Hat: Reduce ?Unsprung Weight? for better handling
and reduces heat-related stress; increases brake performance and pedal feel.
6. Four, Six or Eight Piston Cast
Aluminium Calipers: Provide maximum braking force without the
flex of sliding calipers. Comparison between floating
2-piece and 1-piece discs The floating disc mounting
system, due to the aluminium alloy hat, reduces the ?unsprung?
weight for better handling and reduces heat-related stress: the mounting
system is designed to allow a specific amount of float
in both radial and axial directions. Brembo has engineered special
springs that are used on every other fastener in order
to slightly preload the assembly. This has been done to
prevent excessive noise from the system during street use. The
one-piece discs (both for the Sport and GT lines) are
specifically designed in the goose-neck area to minimize thermal distortion
and thus disc warping under severe use conditions. The one-piece
discs provide excellent stopping power ranging from everyday traffic conditions
to more spirited high performance driving, and fit into the
budget of any enthusiast. Ventilation gap
It is a popular misconception that the slots or drillings
in a disc determinate the direction of rotation. In truth,
for an internally vented disc, the geometry of the vanes
dictates the direction of rotation. There are
3 different ventilation types in use: · Straight vanes
· Curved vanes · Pillars
The straight vanes and the pillars are non-directional, and can
be used on either side of the vehicle. The curved
vane disc, however, is directional. A curved vane disc must
be installed with the vanes running back from the inside
to the outside diameters in the direction of rotation. Orienting
the disc in this manner, creates a centrifugal pump. The
rotation of the disc causes air to be pumped from
the center of the disc, through the vanes, and out
through the outside diameter of the disc. This enhances the
disc?s ability to dissipate hea
$2,595.00
Mazda B-Series Pickup 94-97;
Omni-Gard SE Hood Deflector, Clear
[More]
|
|
Mercury Sable 86-88;
Headlight Cover (Small), Smoke - GTS Head Light covers
will add aerodynamic styling to any car, truck, or SUV.
Designed to help protect today?s expensive headlights, GTS Head Light
covers are easy to install with no drilling or vehicle
modifications required. Available in smoke, clear, and carbon fiber finishes.
Covers are packaged in complete sets and will enhance the
look of any vehicle. GTS Head Light Covers are designed
to complement the Blackout tail light covers.Constructed with GTS composilite
material these headlight covers are tough and durable. The GTS
logo is included along with all installation hardware and instructions.
Headlight Covers ? Adds aerodynamic style
to any vehicle ? No drilling or modifications required
? Custom Designed for each vehicle ? Smoke,
clear, and carbon fiber finishes ? Includes all hardware
and instructions
$75.95
Nissan Titan/Armada Bumper 2004-2006 Grille 1999-2006 Chevrolet (Chevy) Silverado Fleetside, GMC Sierra Fleetside: Rear Bumper Cover (Does Not Interfer W/ Factory Towing Hitch) by Xenon Mercury Cougar 89-97 Lowering Springs, Drop Height: 1.50/1.50 2000-2002 Chevrolet Tahoe - 4WD - Rear Disc Brakes, W/O Limited Slip Axle
Rear LTS Hawk Brake Pads
[More]
|
|
|
1999-2000 Honda Civic
Bomber Complete Body Kit, Duraflex Fiberglass - DURAFLEX technology is a revolutionary
product which combines fiberglass, plastic, and flex resins to obtain
its unique features. DURAFLEX products obtain a much higher durability
rate than the average fiberglass product, reducing shipping damages up
to 75%. Every DURAFLEX product is inspected through a rigorous
quality control process giving consumers the highest quality product available
with superior craftsmanship. This process ensures that DURAFLEX products are
free from normal fiberglass deficiencies including waviness, spider cracks, chips,
and gel coat damage. DURAFLEX products
come finished with a shiny black gel coat, high quality
mesh, hardware kit, and an installation guide. With such attention
to detail, DURAFLEX products are surprisingly affordable, roughly 50% of
the cost of a comparable high quality JDM product. DURAFLEX
products include many advantages of both fiberglass and poly- urethane
aerodynamics, while leaving out most of the disadvantages. In essence,
our new DURAFLEX products will give you the highest quality
product at the most affordable prices.
Features: - Glossy black gel coat finish -
Shiny, high quality metal mesh - Hardware kit
- Installation guide - Reduced damage rate up to
75% - Extremely affordable, roughly half the cost of
Urethane Extreme Dimensions, Inc. is a world renowned
aftermarket automotive aerodynamic company headquartered in the United States. Extreme
Dimensions currently manufacturers and distributes over 6,000 products worldwide including
Europe and Asia. From their humble beginnings in the summer
of 2000, they have striven to offer the largest variety
of high quality aerodynamic products at the most affordable prices.
Extreme Dimensions, Inc. is dedicated to excellent service, meeting and
surpassing all industry standards. Since the beginning, they have been
designing, manufacturing, and distributing aerodynamic parts for the import, domestic,
truck, and SUV industries. Extreme Dimensions has
relocated in 2005 to a new distribution center located in
Southern California which exceeds 50,000 sq/ft to accommodate our growth
and continue to provide excellent customer service. They have pride
themselves in being a service oriented company offering a 95%
fill rate on orders to satisfy our customers needs. What
sets them apart from the competition is that they are
truly a manufacturer, importer, and distributor of fiberglass and carbon
composites, offering the largest selection of aerodynamic products in the
industry. With thousands of parts available, Extreme Dimensions offers you
the choice of fiberglass, high quality Carbon Creations carbon products,
and our new line of DuraFlex products which
combine quality and technology. Our goal is to offer our
loyal customers the most modern and convenient access for up-to-date
and accurate information on our products, which our customers have
come to expect from us. This Complete Kit
Includes Bomber Front Bumper, Bomber Side Skirts, and
$549.00
CoverCraft Interior Covers Sunbrella Burgundy/LG
[More]
|
|
2005-2006 Porsche 997 C2S
Front Drilled Gran Turismo Brake Kit
6 Piston Caliper
Disc Size: 380x32
2 Piece Rotor - Brembo Gran Turismo Brake
System This line is dedicated to the most
demanding customers.This braking system originates from the Racing components, consisting
of a ventilated, integral or composite disc, available drilled or
slotted, 4, 6 and 8 piston aluminium calipers, a complete
set of high performance brake pads, metal braid tubes and
high quality small parts. Please remember that
in the European Community, Gran Turismo products may only be
used in racing and on private roads, unless you have
obtained a new approval in compliance with directive 98/12/EC.
1. High Performance Friction Material: Aggressive
pads that provide the highest level of performance.
2. Cross-Drilled or Slotted Discs: Clears gasses,
cleans pads for better ?bite?. 3. Mounting
Brackets and Assembly Hardware: Aircraft quality included and
pre-torqued specifications. 4. Stainless Steel Braided Brake
Line: DOT/TÃœV approved. 5. ?Floating?
Disc Mounting System with Billet Aluminium Hat: Reduce
?Unsprung Weight? for better handling and reduces heat-related stress; increases
brake performance and pedal feel. 6. Four,
Six or Eight Piston Cast Aluminium Calipers: Provide
maximum braking force without the flex of sliding calipers.
Comparison between floating 2-piece and 1-piece discs
The floating disc mounting system, due to the aluminium
alloy hat, reduces the ?unsprung? weight for better handling and
reduces heat-related stress: the mounting system is designed to allow
a specific amount of float in both radial and axial
directions. Brembo has engineered special springs that are used on
every other fastener in order to slightly preload the assembly.
This has been done to prevent excessive noise from the
system during street use. The one-piece discs (both for the
Sport and GT lines) are specifically designed in the goose-neck
area to minimize thermal distortion and thus disc warping under
severe use conditions. The one-piece discs provide excellent stopping power
ranging from everyday traffic conditions to more spirited high performance
driving, and fit into the budget of any enthusiast.
Ventilation gap It is a popular misconception
that the slots or drillings in a disc determinate the
direction of rotation. In truth, for an internally vented disc,
the geometry of the vanes dictates the direction of rotation.
There are 3 different ventilation types in
use: · Straight vanes · Curved vanes
· Pillars The straight vanes and the
pillars are non-directional, and can be used on either side
of the vehicle. The curved vane disc, however, is directional.
A curved vane disc must be installed with the vanes
running back from the inside to the outside diameters in
the direction of rotation. Orienting the disc in this manner,
creates a centrifugal pump. The rotation of the disc causes
air to be pumped from the center of the disc,
through the vanes, and out through the outside diameter of
the disc. This enhances the disc?s ability to dissipate hea
$4,295.00
2006-2007 Ford Fusion V6;
3D Carbon 5 Piece Body Kit:
Front Air Dam,
Right and Left Side Skirts,
Rear Lower Skirt,
Roof Spoiler,
Exhaust
[More]
|
|
|
1989-1993 Ford Thunderbird / 1989-1993 Mercury Cougar: Right Side Skirt by Xenon - Xenon body styling kits, sport flares
and styling parts are each individually designed. We provide distinctive
automobile accessories that allow automobile, sport truck and SUV owners
an opportunity to stylize and individualize their vehicles. Products are
designed to flow with the vehicles natural lines and meet,
what we believe, are the popular trends on the cutting
edge of automotive fashion. All Xenon styling kits are
offered as individual parts or as a kit. This means
customers can add individualism to their car, sport truck or
SUV. Fits Ford Thunderbird 1989, 1990, 1991,
1992, 1993 Fits Mercury Cougar 1989, 1990, 1991,
1992, 1993 Fits Models: 1992-1993, Ford Thunderbird
LX & Sport Models 1989-1991, Ford Thunderbird V-6 or
V-8 and 1992 Base Model 151A 1989-1993, Mercury Cougar
$189.00
Power Slot Eagle Talon, Non Turbo 95-99 Power Slot Slotted Rotors; Rear Rotors - Rotors Are Directional. Psl = Left
[More]
|
|
|
1989-1994 Nissan 240SX HB
S15 N-1 Conversion, Duraflex Fiberglass - DURAFLEX technology is a revolutionary product which combines
fiberglass, plastic, and flex resins to obtain its unique features.
DURAFLEX products obtain a much higher durability rate than the
average fiberglass product, reducing shipping damages up to 75%. Every
DURAFLEX product is inspected through a rigorous quality control process
giving consumers the highest quality product available with superior craftsmanship.
This process ensures that DURAFLEX products are free from normal
fiberglass deficiencies including waviness, spider cracks, chips, and gel coat
damage. DURAFLEX products come finished with
a shiny black gel coat, high quality mesh, hardware kit,
and an installation guide. With such attention to detail, DURAFLEX
products are surprisingly affordable, roughly 50% of the cost of
a comparable high quality JDM product. DURAFLEX products include many
advantages of both fiberglass and poly- urethane aerodynamics, while leaving
out most of the disadvantages. In essence, our new DURAFLEX
products will give you the highest quality product at the
most affordable prices. Features: -
Glossy black gel coat finish - Shiny, high quality
metal mesh - Hardware kit - Installation guide
- Reduced damage rate up to 75% -
Extremely affordable, roughly half the cost of Urethane
Extreme Dimensions, Inc. is a world renowned aftermarket automotive aerodynamic
company headquartered in the United States. Extreme Dimensions currently manufacturers
and distributes over 6,000 products worldwide including Europe and Asia.
From their humble beginnings in the summer of 2000, they
have striven to offer the largest variety of high quality
aerodynamic products at the most affordable prices. Extreme Dimensions, Inc.
is dedicated to excellent service, meeting and surpassing all industry
standards. Since the beginning, they have been designing, manufacturing, and
distributing aerodynamic parts for the import, domestic, truck, and SUV
industries. Extreme Dimensions has relocated in 2005
to a new distribution center located in Southern California which
exceeds 50,000 sq/ft to accommodate our growth and continue to
provide excellent customer service. They have pride themselves in being
a service oriented company offering a 95% fill rate on
orders to satisfy our customers needs. What sets them apart
from the competition is that they are truly a manufacturer,
importer, and distributor of fiberglass and carbon composites, offering the
largest selection of aerodynamic products in the industry. With thousands
of parts available, Extreme Dimensions offers you the choice of
fiberglass, high quality Carbon Creations carbon products, and our new
line of DuraFlex products which combine quality and
technology. Our goal is to offer our loyal customers the
most modern and convenient access for up-to-date and accurate information
on our products, which our customers have come to expect
from us. This S15 Conversion Includes N-1
Front Bumper, S15 OEM Fiberglass Hood,
$1,799.00
Nissan Altima 4 Cyl 2.5L 02-03
True Flow Intake System
[More]
|
|
|
Power Slot Honda Accord Sedan, Lx & Ex W/ Abs 94-97 Power Slot Slotted And Dimpled Rotors; Rear Rotors - Rotors Are Directional. Dsr = Right - Designed for the performance
enthusiast who wants the look of a cross drilled brake
rotor without the inherent cracking problems, Power Slot's Pro Stop
rotors give you the best of both worlds. Pro Stop
rotors are machined with our highly effective Vac-U-Slot design and
enhanced with a series of dimples that look like drilled
holes. As the brake pad contacts the rotor, the dimples
turn black, simulating the cross-drilled look. All Pro Stop rotors
are made to the same high quality specifications as the
original Power Slot product line, Pro Stop slotted/dimpled rotors are
perfect for show cars or for daily driven vehicles. However
for high performance or severe duty applications, we recommend our
traditional Power Slot slotted brake rotor for maximum effectiveness. Click
Here to view brakes for trucks!
$89.34
1994-2000 Mercury Sable
Front Drilled Sport Brake Rotors
[More]
|
|
2007 Chevrolet Silverado
Black Chrome OE Valance Speed Grille - Speed Grille
Street Scene Equipment brings custom truck
and car fans the hottest product in the automotive marketplace,
the Speed Grille â„¢. Inspired by European racing designs, our
Speed Grilles are available for most popular trucks, SUVs, domestic
and import performance cars, for both the Main Grille and
Lower Valance.
$145.00
Chevrolet Silverado 99-02 / Suburban 00-06 / Tahoe 00-06
Chrome Mesh w/Mirror Bright Trim Sixty Upper Mesh Stainless Wire Mesh Grille 1991-1998 Dodge Dakota
Front HP Superduty Hawk Brake Pads 1992-2000 Honda Civic
Sport Spring
1.5 / 1.5 Front and Rear Lowering MagnaFlow Universal Catalytic Converter, Standard Oval, 1.75" Inch Inlet/Outlet, 12" Inch Body, 16" Inch Overall, 6.5" Inch Wide, Single Air
[More]
|
|
|
1990-1994 Plymouth Laser
Duraflex Fiberglass Bomber Front Bumper - DURAFLEX technology is
a revolutionary product which combines fiberglass, plastic, and flex resins
to obtain its unique features. DURAFLEX products obtain a much
higher durability rate than the average fiberglass product, reducing shipping
damages up to 75%. Every DURAFLEX product is inspected through
a rigorous quality control process giving consumers the highest quality
product available with superior craftsmanship. This process ensures that DURAFLEX
products are free from normal fiberglass deficiencies including waviness, spider
cracks, chips, and gel coat damage.
DURAFLEX products come finished with a shiny black gel coat,
high quality mesh, hardware kit, and an installation guide. With
such attention to detail, DURAFLEX products are surprisingly affordable, roughly
50% of the cost of a comparable high quality JDM
product. DURAFLEX products include many advantages of both fiberglass and
poly- urethane aerodynamics, while leaving out most of the disadvantages.
In essence, our new DURAFLEX products will give you the
highest quality product at the most affordable prices.
Features: - Glossy black gel coat finish
- Shiny, high quality metal mesh - Hardware
kit - Installation guide - Reduced damage rate
up to 75% - Extremely affordable, roughly half the
cost of Urethane Extreme Dimensions, Inc. is a
world renowned aftermarket automotive aerodynamic company headquartered in the United
States. Extreme Dimensions currently manufacturers and distributes over 6,000 products
worldwide including Europe and Asia. From their humble beginnings in
the summer of 2000, they have striven to offer the
largest variety of high quality aerodynamic products at the most
affordable prices. Extreme Dimensions, Inc. is dedicated to excellent service,
meeting and surpassing all industry standards. Since the beginning, they
have been designing, manufacturing, and distributing aerodynamic parts for the
import, domestic, truck, and SUV industries. Extreme
Dimensions has relocated in 2005 to a new distribution center
located in Southern California which exceeds 50,000 sq/ft to accommodate
our growth and continue to provide excellent customer service. They
have pride themselves in being a service oriented company offering
a 95% fill rate on orders to satisfy our customers
needs. What sets them apart from the competition is that
they are truly a manufacturer, importer, and distributor of fiberglass
and carbon composites, offering the largest selection of aerodynamic products
in the industry. With thousands of parts available, Extreme Dimensions
offers you the choice of fiberglass, high quality Carbon Creations
carbon products, and our new line of DuraFlex
products which combine quality and technology. Our goal is to
offer our loyal customers the most modern and convenient access
for up-to-date and accurate information on our products, which our
customers have come to expect from us. Bomber
Front Bumper. NOTE: Fits 90-91 Mitsubishi Eclipse. 92-94 Eclipse R
$229.00
Dodge Ram Long Bed (8 ft) 94-01, 2500-02
Express Tonneau Cover AEM Acura Integra Non VTEC 94-01 Performance; Cold Air Intake System 1995-1997 Toyota Tacoma 4x4: Right Rear Flare by Xenon
[More]
|
|
Power Slot Mitsubishi Galant 2Wd V6 98-00 Power Slot Slotted Rotors; Front Rotors - Rotors Are Directional. Psl = Left - Excessive heat can cause resins in your brake pad to
vaporize or "outgas." As the brake pad wears, the used
friction material turns into a fine dust. This boundary layer
of heat, gas and dust builds up between the pad
and rotor surfaces and inhibits performance. Here's where Power Slot's
slotted brake rotors make a big difference. Power Slot's exclusive
Vac-U-Slots are machined into the rotor and help evacuate gasses
and dust, shed heat, and keep the brake pad surface
clean. And in wet, raining conditions, our Vac-U-Slot helps push
water off the braking surface for better stopping power. The
Vac-U-Slot also serves as a visual wear indicator. The slot
is machined to the rotor?s minimum thickness where it crosses
the outside edge. If you cannot see the slot along
the outside edge, the rotor has worn down to its
discard depth. Click Here to view brakes for trucks!
$114.48
1978-1983 Pontiac Bonneville, Catalina, Firebird, Grand Am, Grand Lemans, Grand Prix, Laurentian (Canadian), Lemans, Parisienne:
V6 3.8L - Code A Eng. 231 c
[More]
|
|
|
72-80 Jeep CJ5, 6, 7, 258 cu.in.
PaceSetter Header - 1-1/2" Tubing Diameter, 2-1/4" Collector, Flanged Collector, Hook-ups
for smog and engine management senors. Comes with collector reducer.
Fabrication required to hook to exhaust system. 50 State Legal.
Fits Jeep CJ5, 6, 7 1972, 1973, 1974, 1975, 1976,
1977, 1978, 1979, 1980. Picture shown is a generic picture
and does not represent product exactly.
$449.95
1996-2002 Chevrolet G20, 2500 Series, Express (3/4 Ton) Van - 7300 Lb. Gvw
Front HP Superduty Hawk Brake Pads
[More]
|
|
|
1991-1995 Plymouth Acclaim - Rear Disc Brakes, 15" Wheels
Rear Performance Ceramic Hawk Brake Pads - Performance Ceramic
Ultimate stopping power in an ultra-low dust, low noise
ceramic compound! Hawk Performance has introduced a premium,
high performance, ultra-low dust, low noise compound called Performance Ceramic.
Performance Ceramic is engineered to reduce brake
NVH (Noise, Vibration and Harshness), creating a quieter performing brake
pad. Furthermore, the ceramic brake pad formula has a linear
friction profile that allows your ABS brake system to work
more effectively. With Performance Ceramic you can expect reduced brake
pad wear, lower dust output levels and a rotor-friendly brake
pad. Performance Ceramic ? quiet, clean
& fast stopping! Key Features:
? Increased stopping power ? Increased rotor life
? Extended pad life ? Ultra-low dust ?
Extremely quiet ? Stable friction output ? Recommended
for import domestic automobiles, luxury SUV?s, sports trucks & vans.
Today?s alloy wheel designs on premium
vehicles has contributed to customer demand for a low dust
performance brake product. Specify Hawk Performance?s Performance Ceramic brake pads
for your luxury car, SUV, or truck.
All Hawk Performance Performance Ceramic brake pads provide a
limited lifetime warranty, ensuring products to be free of defects
from manufacturer?s workmanship and materials. Note:
Hawk Performance burnishes its Performance Ceramic brake pads as a
final step in the factory, but all brake pads have
to be bedded-in with the rotors (new or used) that
they will be used against. Properly bedding-in new brake pads
results in a transfer film being generated at the pad
and rotor interface to maximize brake performance
Brake Pad Installation Procedure 1. Install brake pads
properly. Be sure pads are securely positioned in the caliper.
2. Flush system with fresh brake fluid.
3. Check all hydraulic parts for excess
wear and tear. 4. Check disc for
proper thickness, parallelism, and lateral runout. 5.
Check disc for scoring or grooves over .012?depth. If either
applies, resurfacing is required. 6. If discs
do not need resurfacing, then contamination from the previous brake
pads must be removed. Sand discs with 130 grit sandpaper
using moderate pressure. Use soap and water to clean discs?
surface after sanding and machining. Discs should be free and
clear of oil, grease, and brake fluid.
7. Inspect calipers for freedom of movement. Lubricate where necessary.
Burnishing Instructions 1. After
installing new brake pads, make 6 to 10 stops from
approximately 30-35 mph applying moderate pressure. 2.
Make an additional 2 to 3 hard stops from approximately
40 to 45 mph. 3. DO NOT
DRAG BRAKES! 4. Allow 15 minutes for
brake system to cool down. 5. After
step 4 your new pads are ready for use.
$74.44
Putco Chevrolet (Chevy) Silverado (2Dr) 99-05 Chrome Trim Door Handles; 8-Ball Style (Center Only) 1989-1993 Mitsubishi Eclipse
Front Drilled Sport Brake Rotors
[More]
|
|
Air Lift Company Chevrolet (Chevy) K-30 1 Ton Pickup 4WD 73-87 Vehicle Specific Air Assist Kits; Super Duty Air Spring Kit (Rear) - Fits
Chevrolet (Chevy) K-30 1 Ton Pickup 4WD 1973, 1974, 1975,
1976, 1977, 1978, 1979, 1980, 1981, 1982, 1983, 1984, 1985,
1986, 1987 57000 Series
Air Lift's Super Duty kits are the heaviest
rated kits for real suspension muscle. These kits use 2-ply
fabric reinforced airsprings which are built like a tire. Load
-leveling ratings vary y kit - from 3,000 to 5000
lbs depending on the size of the air springs. The
Super Duty air springs are molded with high - strength
Zytel® nylon. It is as strong as steel but weighs
less and is corrosion proof. Airlift takes pride in their
manufacturing process and quality standards so you can purchase this
product with confidence. •
Rear kits for 3/4 and 1 ton pickups and vans
for hauling or towing.
• Rear kits for commercial work trucks: wreckers, ambulances, construction
trucks, and other severe use.
• Front kits for leaf sprung Class "A" Motorhomes
and 4WD pickups.
Other Benefits of Air Lift Assist
Kits •
Up to 5,000 lbs. of leveling capacity. *
• Air Adjustable from 5 to 100 psi.
• Vehicle specific illustrated installation manuals.
• Engineered for easy installation - 2 hours.
• Quick - connect DOT air fittings.
• Neoprene chemical resistant construction - more durable
than rubber. * Never
exceed Manufacturers recommended Gross Vehicle Weight Rating
$335.00
Street Scene Ford F-150 97 Mirrors; Electric Power Slot Volkswagen Jetta Gls Vr6, Gls Turbo, Glx W/ Solid Rear Disc (Mk Iv Chassis) 99-05 Power Slot Slotted Rotors; Rear Rotors - Rotors Are Directional. Ps 1995-1999 Saturn SL1, SOHC, 1991-1999 SL2, DOHC, 2000-2002 S Series, SOHC (No CARB for 00-02 Sseries)
Short Ram Intake System, Black Powder Coat
Filter: Chevrolet S10 Pickup 83-93, S15 Pickup 83-90, Blazer / Jimmy 83-94;
Bug-Gard Hood Deflector (Large), Clear
[More]
|
|
|
1992-1993 Cadillac Seville
Rear HPS Hawk Brake Pads - HPS - High Performance Street
Superior Stopping Power HPS -
High Performance Street disc brake pads are world renowned for
increasing stopping power on your street legal vehicle. Increasing the
performance of your vehicles braking system is easy when you
choose Hawk Performance?s HPS braking compound. This unique Ferro-Carbon formula
was developed for street performance using the safety and quality
of Aerospace and Motorsports severe-duty friction technology.
The High Performance Street compound offers a higher coefficient of
friction over stock brake pads and can provide you 20-40%
more stopping power and higher resistance to brake fade than
most standard replacement pads. Less fade means you?ll have a
highly durable brake pad with less brake dust..
HPS Ferro-Compound Features: ? Increased stopping power
? High friction/torque hot or cold
? Gentle on rotors ? Extended pad life
? Low dust ? Virtually noise-free
All Hawk Performance High Performance
Street brake pads provide a limited lifetime warranty, ensuring products
to be free of defects from manufacturer?s workmanship and materials.
Note: Hawk Performance burnishes
its High Performance Street brake pads as a final step
in the factory, but all brake pads have to be
bedded-in with the rotors (new or used) that they will
be used against. Properly bedding-in new brake pads results in
a transfer film being generated at the pad and rotor
interface to maximize brake performance. Brake
Pad Installation Procedure 1. Install brake pads properly.
Be sure pads are securely positioned in the caliper.
2. Flush system with fresh brake fluid.
3. Check all hydraulic parts for excess wear
and tear. 4. Check disc for proper
thickness, parallelism, and lateral runout. 5. Check
disc for scoring or grooves over .012?depth. If either applies,
resurfacing is required. 6. If discs do
not need resurfacing, then contamination from the previous brake pads
must be removed. Sand discs with 130 grit sandpaper using
moderate pressure. Use soap and water to clean discs? surface
after sanding and machining. Discs should be free and clear
of oil, grease, and brake fluid. 7.
Inspect calipers for freedom of movement. Lubricate where necessary.
Burnishing Instructions 1. After installing
new brake pads, make 6 to 10 stops from approximately
30-35 mph applying moderate pressure. 2. Make
an additional 2 to 3 hard stops from approximately 40
to 45 mph. 3. DO NOT DRAG
BRAKES! 4. Allow 15 minutes for brake
system to cool down. 5. After step
4 your new pads are ready for use.
$67.00
1997-2002 Toyota 4Runner Base Model
Running Board Bracket Mazda MPV 00-04;
Bug-Gard Hood Deflector SE, Smoke 1982-1993 Chevrolet Chevy / GMC S Series PU / 83-94 S Blazer / Jimmy; Grille Assembly - Chrome - w/Phantom Billet Installed - No Recess needed (Horizontal)
[More]
|
|
2000-2005 Mitsubishi Galant - Exc. Galant Sigma V6 - V6
Rear Performance Ceramic Hawk Brake Pads - Performance Ceramic Ultimate
stopping power in an ultra-low dust, low noise ceramic compound!
Hawk Performance has introduced a premium, high performance,
ultra-low dust, low noise compound called Performance Ceramic.
Performance Ceramic is engineered to reduce brake NVH (Noise,
Vibration and Harshness), creating a quieter performing brake pad. Furthermore,
the ceramic brake pad formula has a linear friction profile
that allows your ABS brake system to work more effectively.
With Performance Ceramic you can expect reduced brake pad wear,
lower dust output levels and a rotor-friendly brake pad.
Performance Ceramic ? quiet, clean & fast
stopping! Key Features: ? Increased
stopping power ? Increased rotor life ? Extended
pad life ? Ultra-low dust ? Extremely quiet
? Stable friction output ? Recommended for import
domestic automobiles, luxury SUV?s, sports trucks & vans.
Today?s alloy wheel designs on premium vehicles has
contributed to customer demand for a low dust performance brake
product. Specify Hawk Performance?s Performance Ceramic brake pads for your
luxury car, SUV, or truck. All
Hawk Performance Performance Ceramic brake pads provide a limited lifetime
warranty, ensuring products to be free of defects from manufacturer?s
workmanship and materials. Note: Hawk Performance
burnishes its Performance Ceramic brake pads as a final step
in the factory, but all brake pads have to be
bedded-in with the rotors (new or used) that they will
be used against. Properly bedding-in new brake pads results in
a transfer film being generated at the pad and rotor
interface to maximize brake performance Brake Pad
Installation Procedure 1. Install brake pads properly. Be
sure pads are securely positioned in the caliper.
2. Flush system with fresh brake fluid.
3. Check all hydraulic parts for excess wear and
tear. 4. Check disc for proper thickness,
parallelism, and lateral runout. 5. Check disc
for scoring or grooves over .012?depth. If either applies, resurfacing
is required. 6. If discs do not
need resurfacing, then contamination from the previous brake pads must
be removed. Sand discs with 130 grit sandpaper using moderate
pressure. Use soap and water to clean discs? surface after
sanding and machining. Discs should be free and clear of
oil, grease, and brake fluid. 7. Inspect
calipers for freedom of movement. Lubricate where necessary.
Burnishing Instructions 1. After installing new
brake pads, make 6 to 10 stops from approximately 30-35
mph applying moderate pressure. 2. Make an
additional 2 to 3 hard stops from approximately 40 to
45 mph. 3. DO NOT DRAG BRAKES!
4. Allow 15 minutes for brake system
to cool down. 5. After step 4
your new pads are ready for use.
$70.40
1999-2001 Hyundai Tiburon
Front Drilled Sport Brake Rotors 2007-2007 Chevrolet Suburban 6.0L
DiabloSport Predator Hand Held Flash Programmer 1991-1993 Honda Accord Station Wagon: Body Kit (4 Pieces) by Xenon Dodge Ram 94-01
Steel Cowl Induction Hood (Primed)
[More]
|
|
|
Ryno Manufacturing
GM Fullsize Truck 85-06 Billet Accessories;
Blue Billet Pedal Kit "SCALLOP" - Ryno Manufacturing uses
state of the art technology to produce one of a
kind Billet Accessories that are seen in some of today?s
top show cars and trucks, such as 85-Current Full Size
Trucks and SUV's. Ryno Manufacturing quality control
program assures that each Blue Pedal Kit "Scallop" Billet Accessory
leaves Ryno Manufacturing facility with Ryno Manufacturing 100% satisfaction.
Centrally located in Bakersfield, Ca. Ryno Manufacturing is
on the cutting edge of what?s new and hot in
Billet Accessories in the car and truck automotive industry for
85-Current Full Size Trucks and SUV's. Check
out Ryno Manufacturing full line of Billet Accessory products like
Blue Pedal Kit "Scallop" and see why everyone wants Ryno
Manufacturing Billet Accessories on their cars and trucks such as
85-Current Full Size Trucks and SUV's. Customer
satisfaction in Billet Accessories is Ryno Manufacturing primary goal says
President Ryan Martens. Ryno Manufacturing says when
getting Billet Accessories such as Blue Pedal Kit "Scallop" for
your truck, a 85-Current Full Size Trucks and SUV's:
?Choose the best choose Ryno?
$118.75
2000-2004 Toyota Tundra:
V8 4.7L - P/S;
MagnaFlow Direct Fit Catalytic Converter
[More]
|
|
|
Chevrolet Astro Van 95, Safari Van 95-05;
Headlight Cover (Large), Smoke - GTS Head Light covers will add aerodynamic styling to any
car, truck, or SUV. Designed to help protect today?s expensive
headlights, GTS Head Light covers are easy to install with
no drilling or vehicle modifications required. Available in smoke, clear,
and carbon fiber finishes. Covers are packaged in complete sets
and will enhance the look of any vehicle. GTS Head
Light Covers are designed to complement the Blackout tail light
covers.Constructed with GTS composilite material these headlight covers are tough
and durable. The GTS logo is included along with all
installation hardware and instructions. Headlight Covers
? Adds aerodynamic style to any vehicle ? No
drilling or modifications required ? Custom Designed for each
vehicle ? Smoke, clear, and carbon fiber finishes
? Includes all hardware and instructions
$102.95
1999-2005 Volkswagen Passat - Exc. Syncro, W8
Rear HPS Hawk Brake Pads 2004-2005 Ford F-150 SuperCrew, Flareside: Body Kit (8 Pieces) by Xenon
[More]
|
|
|
1993-1997 Nissan Altima
R33 Complete Body Kit, Duraflex Fiberglass - DURAFLEX technology is a revolutionary product which combines
fiberglass, plastic, and flex resins to obtain its unique features.
DURAFLEX products obtain a much higher durability rate than the
average fiberglass product, reducing shipping damages up to 75%. Every
DURAFLEX product is inspected through a rigorous quality control process
giving consumers the highest quality product available with superior craftsmanship.
This process ensures that DURAFLEX products are free from normal
fiberglass deficiencies including waviness, spider cracks, chips, and gel coat
damage. DURAFLEX products come finished with
a shiny black gel coat, high quality mesh, hardware kit,
and an installation guide. With such attention to detail, DURAFLEX
products are surprisingly affordable, roughly 50% of the cost of
a comparable high quality JDM product. DURAFLEX products include many
advantages of both fiberglass and poly- urethane aerodynamics, while leaving
out most of the disadvantages. In essence, our new DURAFLEX
products will give you the highest quality product at the
most affordable prices. Features: -
Glossy black gel coat finish - Shiny, high quality
metal mesh - Hardware kit - Installation guide
- Reduced damage rate up to 75% -
Extremely affordable, roughly half the cost of Urethane
Extreme Dimensions, Inc. is a world renowned aftermarket automotive aerodynamic
company headquartered in the United States. Extreme Dimensions currently manufacturers
and distributes over 6,000 products worldwide including Europe and Asia.
From their humble beginnings in the summer of 2000, they
have striven to offer the largest variety of high quality
aerodynamic products at the most affordable prices. Extreme Dimensions, Inc.
is dedicated to excellent service, meeting and surpassing all industry
standards. Since the beginning, they have been designing, manufacturing, and
distributing aerodynamic parts for the import, domestic, truck, and SUV
industries. Extreme Dimensions has relocated in 2005
to a new distribution center located in Southern California which
exceeds 50,000 sq/ft to accommodate our growth and continue to
provide excellent customer service. They have pride themselves in being
a service oriented company offering a 95% fill rate on
orders to satisfy our customers needs. What sets them apart
from the competition is that they are truly a manufacturer,
importer, and distributor of fiberglass and carbon composites, offering the
largest selection of aerodynamic products in the industry. With thousands
of parts available, Extreme Dimensions offers you the choice of
fiberglass, high quality Carbon Creations carbon products, and our new
line of DuraFlex products which combine quality and
technology. Our goal is to offer our loyal customers the
most modern and convenient access for up-to-date and accurate information
on our products, which our customers have come to expect
from us. This Complete Kit Includes R33
Front Bumper, R34 Side Skirts, and R34
$749.00
Ford Mustang / GT 83-93;
Vent-Gard Side Window Deflector 1994-1999 Dodge:
Front Power Slot Cryo Rotor
Left 2001-2003 Isuzu Rodeo
Uni Series Non-Lighted Running Board 72" Nissan Titan King Cab 04-06 (without rail system)
Tool Box Tonno Tonneau Cover
[More]
|
|
2001-2003 Isuzu Rodeo
Uni Series Non-Lighted Running Board 72" - ATS
Designis a leading manufacturer of light truck and SUV styling
products such as, universal and custom running boards, fender flares
and automotive universal wings. Established in 1991, ATS Design has
adopted the mission of providing ?quality products that meet and
exceed [their] customer?s expectations and to deliver them on time,
every time, defect free.? ATS Design started with the vision
of creating factory replicas and universal wings for the automotive
aftermarket. With the success of the wing, ATS decided to
penetrate the truck and SUV market by designing and manufacturing
various accessories for these applications such as: running boards, fender
flares and valances. ATS Design has the
capability and adaptability to meet the needs of the changing
market. Unlike the competition, ATS does not utilize overseas facilities.
ATS?s 120,000 sqft. Manufacturing facilities are located in California, which
gives ATS the added advantage of control over production and
quality assurance. This also allows ATS to be more flexible
in innovating and producing demand-based products. All of the ATS
Designs products meet and/or exceed OE standard, which has earned
them the reputation of being ?America?s premiere and only automated
aftermarket painting facility?. With the dedication and continued commitment to
quality, ATS is an ISO 9002 certified company.
$450.80
AEM Toyota Camry 6Cyl (1MZ-FE Only) 94-95 Air Intake; Cold Air Induction System - Polished
[More]
|
|
|
Chevrolet S-10 Blazer 95-97;
Headlight Cover (Small), Clear - GTS Head Light covers will add aerodynamic styling to any
car, truck, or SUV. Designed to help protect today?s expensive
headlights, GTS Head Light covers are easy to install with
no drilling or vehicle modifications required. Available in smoke, clear,
and carbon fiber finishes. Covers are packaged in complete sets
and will enhance the look of any vehicle. GTS Head
Light Covers are designed to complement the Blackout tail light
covers.Constructed with GTS composilite material these headlight covers are tough
and durable. The GTS logo is included along with all
installation hardware and instructions. Headlight Covers
? Adds aerodynamic style to any vehicle ? No
drilling or modifications required ? Custom Designed for each
vehicle ? Smoke, clear, and carbon fiber finishes
? Includes all hardware and instructions
$75.95
Isuzu Pickup / Hombre 96-00;
Headlight Cover (Small), Carbon Fiber 1989-1989 Porsche 944 S, S2
Front And Rear HPS Hawk Brake Pads
[More]
|
|
|
Universal Vader Wing
Duraflex Fiberglass - DURAFLEX technology is a
revolutionary product which combines fiberglass, plastic, and flex resins to
obtain its unique features. DURAFLEX products obtain a much higher
durability rate than the average fiberglass product, reducing shipping damages
up to 75%. Every DURAFLEX product is inspected through a
rigorous quality control process giving consumers the highest quality product
available with superior craftsmanship. This process ensures that DURAFLEX products
are free from normal fiberglass deficiencies including waviness, spider cracks,
chips, and gel coat damage. DURAFLEX
products come finished with a shiny black gel coat, high
quality mesh, hardware kit, and an installation guide. With such
attention to detail, DURAFLEX products are surprisingly affordable, roughly 50%
of the cost of a comparable high quality JDM product.
DURAFLEX products include many advantages of both fiberglass and poly-
urethane aerodynamics, while leaving out most of the disadvantages. In
essence, our new DURAFLEX products will give you the highest
quality product at the most affordable prices.
Features: - Glossy black gel coat finish
- Shiny, high quality metal mesh - Hardware kit
- Installation guide - Reduced damage rate up
to 75% - Extremely affordable, roughly half the cost
of Urethane Extreme Dimensions, Inc. is a world
renowned aftermarket automotive aerodynamic company headquartered in the United States.
Extreme Dimensions currently manufacturers and distributes over 6,000 products worldwide
including Europe and Asia. From their humble beginnings in the
summer of 2000, they have striven to offer the largest
variety of high quality aerodynamic products at the most affordable
prices. Extreme Dimensions, Inc. is dedicated to excellent service, meeting
and surpassing all industry standards. Since the beginning, they have
been designing, manufacturing, and distributing aerodynamic parts for the import,
domestic, truck, and SUV industries. Extreme Dimensions
has relocated in 2005 to a new distribution center located
in Southern California which exceeds 50,000 sq/ft to accommodate our
growth and continue to provide excellent customer service. They have
pride themselves in being a service oriented company offering a
95% fill rate on orders to satisfy our customers needs.
What sets them apart from the competition is that they
are truly a manufacturer, importer, and distributor of fiberglass and
carbon composites, offering the largest selection of aerodynamic products in
the industry. With thousands of parts available, Extreme Dimensions offers
you the choice of fiberglass, high quality Carbon Creations carbon
products, and our new line of DuraFlex products
which combine quality and technology. Our goal is to offer
our loyal customers the most modern and convenient access for
up-to-date and accurate information on our products, which our customers
have come to expect from us. Universal Vader
Wing. NOTE: This wing is 57" wide from tip to
tip and 34"
$249.00
Ford Ranger 04-06;
Bug-Gard Hood Deflector SE, Smoke 1989-1997 Nissan:
Rear Power Slot Cryo Rotor
Left
[More]
|
|
|
Chevrolet/GMC Pickup 88-99, Blazer / Yukon / Suburban / Tahoe 92-99;
Taillight Blackout Cover (Small), Carbon Fiber - GTS Blackout Tail Light covers will add dynamic styling
to any car, truck, or SUV. Designed to help protect
today?s expensive tail lights, GTS Blackout Tail Light covers are
easy to install with no drilling or vehicle modifications required.
Available in smoke and carbon finishes. Covers are packaged in
complete sets. GTS Blackouts will enhance the look of any
vehicle and designed to complement the GTS Head Light covers.
Constructed with GTS Composilite material these tail light covers are
tough and durable. The GTS logo is included along with
all installation hardware and instructions. Taillight Blackout
Covers ? Adds dynamic styling to any vehicle
? No drilling/modifications required ? Custom designed for each
vehicle ? Available in smoke and carbon fiber
? Compliments GTS Headlight Covers ? Includes hardware and
instructions
$84.95
Mitsubishi Lancer OZ Edition 02-06 Lowering Springs, Drop Height: 1.80/1.80
[More]
|
|
Chevrolet/GMC Step 88-98
Blackmax Tonneau Cover - BlackMax Tonneau
Truck Bed Cover by ExtangFits Chevy/GMC Step 88-98The Bold, All
Black Tonno With Head-Turning Good Looks The BlackMax Tonneau Cover
is Engineered to be Superior for Your Chevy/GMC Step 88-98
Truck:When solid black tonneau is the bold good look you
want for your Chevy/GMC Step 88-98 Truck.Exclusive patented all-climate engineered
design that's 4-way fully adjustable for cold weather.Snaps along cab
rail allows quick and easy access into the front of
your Chevy/GMC Step 88-98 Truck bed.NO drilling, NO damage to
your Chevy/GMC Step 88-98!SpringLock bows-easy to install and they'll never
fall off your Chevy/GMC Step 88-98 Truck.One-finger removal of tail
rail using the LeverLock system allows quick access for hauling
large loads with your Chevy/GMC Step 88-98. No hassles or
tools.SnapStopper keeps snaps on the rail when tarp is rolled
up for bulk hauling.The BlackMax features fiberglass reinforced nylon snaps
that will not break.Best warranties for your Chevy/GMC Step 88-98
Truck: 10 years on tarp, and lifetime on frame!Famous Extang
engineering, quality workmanship and excellent customer service.Drop your Chevy/GMC Step
88-98 Truck tailgate with tonno on. One Finger Tonneau Removal:The
BlackMax corners feature Extang's impressive new LeverLock attachment. Pull back
the lever and the tail rail unlocks and quickly disengages
for bulk hauling. When the lever latches you know it's
locked. LeverLock securely stays in place and will not vibrate
loose. All this with one finger! Tarps Designed for Strength
and Good Looks on Your Chevy/GMC Step 88-98 Truck:Corners don't
buckle up due to parachute grade nylon corner reinforcements. Snaps
and corners are backed with thick polymer forcing the corners
and edges to lie smooth and look good in any
weather. The thick polymer edging also keeps your snaps from
ripping out! Quicker Installation on Your Chevy/GMC Step 88-98 Truck:Our
TUFFKLAMPS simply drop into the rail channels (works well with
bed liners). Easy on your Chevy/GMC Step 88-98and clamps tight
to the Truck. Quick Access to Front of Your Chevy/GMC
Step 88-98 Truck Bed:Quickly place items in the bed near
your cab door, snap on the tarp, jump in and
go! Snaps are Your Chevy/GMC Step 88-98 Truck Tonno's
Most Important Part:Fiberglass reinforced nylon formula makes the BlackMax's snaps
strong and durable. Tested and proven under intense usage for
years in the lab and field. Extang's patented MAXSNAPS will
not break. BlaxMax on Your Chevy/GMC Step 88-98 Truck Tonno
has Bow Height AdjustmentExtang's Monster Bows quickly spring on and
off with no tools. It's fast and easily done with
one hand. The TUFFKLAMPS allow two bow heights: HIGH for
maximum water shedding in harsh weather, and for improved gas
mileage. LOW for sporty good looks and cold weather tonno
attachment. Extang Makes the ONLY Chevy/GMC Step 88-98 Truck
Tonnos that Work Well in Cold ClimatesStud low for tight
fit in hot weather Slide off, flip over, then slide
on again Stud high f
$271.00
2003-2004 Volkswagen Jetta VR6, 6 Speed
Cold Air Intake System, Polished 24 Valve
Filter: X-1010 Air Ride Technology Universal Air Suspension Shock and Shockwave Brackets; Shock Tab (Sway Bar Mount) Mounting Tab (10pk) 1999-2005 Pontiac Grand Am
Rear Air Suspension Kit (1/4" Ports) Ford Mustang Cobra 94-95; Mass Air Flow Sensor 24lb Injectors Chrome
[More]
|
|
DC Sports Honda Accord, EX 94-97 4-2-1 Ceramic Header, Two Piece - DC Sports 4-into-1 and
4-2-1 header systems are dyno tested to outperform all comparable
header systems on the market. Extensive research and development goes
into each system to ensure the best performance for your
vehicle. DC Sports header systems are precision bent on our
CNC mandrel benders using data acquired from our non-contact digitizing
scanner. Our flanges are CNC machined, we machine-grind the flange-mating
surface to ensure a leak-free seal, and use a robotic
welder to attach the flange to the header pipes. Our
state-of-the-art manufacturing process ensures superior quality and a perfect fit
with every header system we make. DC Sports has several
50-state legal header designs to choose from. These include a
race-inspired 4-into-1 design that optimizes mid- to top-end power, a
lightweight, one-piece 4-2-1 design that provides maximum ground clearance and
emphasizes low- to mid-range power for street/drag applications, a two-piece
4-2-1 design for easy installation and unmatched low- to mid-range
power, and a 3-into-1 design for V6 applications. We are
also proud to offer "Race-Only" headers in 4-into-1 and 4-2-1
designs (not C.A.R.B. exempt) for off-road applications only.
$457.01
1999-2006
GMC 3500 6.0/6.6L
Volant Ram Air Scoop BMW 3 Series 4dr 99-01 2 Leg Factory Style Wing No Light Power Slot Mercury Mountaineer, 2Wd 97-01 Power Slot Slotted And Dimpled Rotors; Front Rotors - Rotors Are Directional. Dsl = Left
[More]
|
|
2002-2004 Chevrolet Avalanche * (non-lighted boards recommended)
X-treme II Series Lighted Primed Running Board 80" Paintable W/Rubber Step Pad - ATS Designis a leading manufacturer of light truck and
SUV styling products such as, universal and custom running boards,
fender flares and automotive universal wings. Established in 1991, ATS
Design has adopted the mission of providing ?quality products that
meet and exceed [their] customer?s expectations and to deliver them
on time, every time, defect free.? ATS Design started with
the vision of creating factory replicas and universal wings for
the automotive aftermarket. With the success of the wing, ATS
decided to penetrate the truck and SUV market by designing
and manufacturing various accessories for these applications such as: running
boards, fender flares and valances. ATS Design
has the capability and adaptability to meet the needs of
the changing market. Unlike the competition, ATS does not utilize
overseas facilities. ATS?s 120,000 sqft. Manufacturing facilities are located in
California, which gives ATS the added advantage of control over
production and quality assurance. This also allows ATS to be
more flexible in innovating and producing demand-based products. All of
the ATS Designs products meet and/or exceed OE standard, which
has earned them the reputation of being ?America?s premiere and
only automated aftermarket painting facility?. With the dedication and continued
commitment to quality, ATS is an ISO 9002 certified company.
$600.00
1992-2000 Chevrolet Suburban 2500 4WD
Front Drilled Sport Brake Rotors 2004-2004 Chevrolet Silverado 1500 2WD, 4WD, 2-Door, Extended Cab-Standard Duty w/ 4-Wheel Steering, SS w/ 6.0L
Front Drilled Sport Brake Rotors 1993-1995 Mazda:
Rear Power Slot Slotted Rotor
Right
[More]
|
|
|
Easy Street Chevy 1/2 Ton Gen I Vehicle Kits 88-98 Rear Air Bag Kit- (3/8" Ports) - Kits come with
air struts or bellows, brackets, all attaching hardware, and an
illustrated installation manual. Fits Easy Street Chevy 1/2 Ton Gen
I Vehicle Kits 1988, 1989, 1990, 1991, 1992, 1993, 1994,
1995, 1996, 1997, 1998. Complete details and Instructions
$1,295.00
2000-2004 Toyota Tundra V8 4.7L
Power-Flow Air Intake System, Polished with MR Technology & Power Shield only
Filter: X-1015
[More]
|
|
|
2002-2006 Dodge Ram 1500/2500/3500 (Except 2002 Dodge Ram 2500/3500): Right Front Fender Flare (Also Fits Dually Front) by Xenon - Xenon body styling kits,
sport flares and styling parts are each individually designed. We
provide distinctive automobile accessories that allow automobile, sport truck and
SUV owners an opportunity to stylize and individualize their vehicles.
Products are designed to flow with the vehicles natural lines
and meet, what we believe, are the popular trends on
the cutting edge of automotive fashion. All Xenon styling
kits are offered as individual parts or as a kit.
This means customers can add individualism to their car, sport
truck or SUV. Fits Dodge Ram 2002,
2003, 2004, 2005, 2006 Fits Models: 2006,
Dodge Ram, 1500, 2500, 3500, 4 Dr. 2003-2005, Dodge
Ram 2500/3500, 4 Door, Short Bed 2002-2005, Dodge Ram
1500, 4 Door, Short Bed 2002-2005, Dodge Ram 1500,
Standard Cab
$151.00
Mazda Protege 4dr 99-00;
Headlight Cover (Small), Clear AEM Nissan Sentra SE-R Including Spec V 02-03 Performance; Cold Air Intake System Power Slot Volkswagen Scirocco, 16 Valve 86-89 Power Slot Slotted And Dimpled Rotors; Front Rotors - Rotors Are Directional. Dsr = Right 2002-2005 Infiniti Q45
Rear Performance Ceramic Hawk Brake Pads
[More]
|
|
|
2003-2004 Chevrolet Avalanche with No Cladding
X-Treme II Series Primed Running Board 93" Polished Aluminum Diamond Plate Step Pad - ATS Designis a leading manufacturer of light truck and SUV
styling products such as, universal and custom running boards, fender
flares and automotive universal wings. Established in 1991, ATS Design
has adopted the mission of providing ?quality products that meet
and exceed [their] customer?s expectations and to deliver them on
time, every time, defect free.? ATS Design started with the
vision of creating factory replicas and universal wings for the
automotive aftermarket. With the success of the wing, ATS decided
to penetrate the truck and SUV market by designing and
manufacturing various accessories for these applications such as: running boards,
fender flares and valances. ATS Design has
the capability and adaptability to meet the needs of the
changing market. Unlike the competition, ATS does not utilize overseas
facilities. ATS?s 120,000 sqft. Manufacturing facilities are located in California,
which gives ATS the added advantage of control over production
and quality assurance. This also allows ATS to be more
flexible in innovating and producing demand-based products. All of the
ATS Designs products meet and/or exceed OE standard, which has
earned them the reputation of being ?America?s premiere and only
automated aftermarket painting facility?. With the dedication and continued commitment
to quality, ATS is an ISO 9002 certified company.
$168.26
1993-1997 Chevrolet Blazer (S-Series 2WD);
2" Drop Spindle Conversion Kit (Front) 2002-2004 Ford Focus ZX5
Duraflex Fiberglass Poison Front Bumper 2002-2002 Cadillac Ext
Front HPS Hawk Brake Pads 2003-2003 Chrysler Sebring Coupe - 6 Cyl
Front HPS Hawk Brake Pads
[More]
|
|
|
1996-1997 Honda Accord 2 & 4 Door, Station Wagon: Body Kit (4 Pieces) Does Not Fit V6 by Xenon - Xenon body
styling kits, sport flares and styling parts are each individually
designed. We provide distinctive automobile accessories that allow automobile, sport
truck and SUV owners an opportunity to stylize and individualize
their vehicles. Products are designed to flow with the vehicles
natural lines and meet, what we believe, are the popular
trends on the cutting edge of automotive fashion. All
Xenon styling kits are offered as individual parts or as
a kit. This means customers can add individualism to their
car, sport truck or SUV. Fits Honda
Accord 1996, 1997 Fits Models: 1996-1997, Honda
Accord Coupe, 4 Door Sedan, & Station Wagon
This kit Contains: 5731, Air Dam (Does Not Fit V-6
Model) 5732, Right Side Skirt 5733,
Left Side Skirt 5738, Station Wagon Rear Valance
$1,166.00
1988-1996 GMC C3500 Pickup - 1 Ton 2WD - Single Rear Wheels
Front HPS Hawk Brake Pads 1978-1982 Mercury Capri, Cougar, Zephyr:
V8 4.2L - Rear Converter;
MagnaFlow Direct Fit Catalytic Converter 2002-2005 BMW Mini Cooper (Base): Right Side Skirt by Xenon
[More]
|
|
|
1996-1998 Honda Civic 2 Dr Replacement Front Fascia (Includes Mesh)- Also Fits 4 Dr. And Hatchback by Xenon - Xenon body styling kits, sport flares and
styling parts are each individually designed. We provide distinctive automobile
accessories that allow automobile, sport truck and SUV owners an
opportunity to stylize and individualize their vehicles. Products are designed
to flow with the vehicles natural lines and meet, what
we believe, are the popular trends on the cutting edge
of automotive fashion. All Xenon styling kits are offered
as individual parts or as a kit. This means customers
can add individualism to their car, sport truck or SUV.
Fits Honda Civic 1996, 1997, 1998
Fits Models: 1996-1998, Honda Civic, Coupe
$530.00
1973 - 1987
Chevrolet 1500
Chevrolet 2500
Chevrolet 3500
GMC 1500
GMC 2500
GMC 3500
Truck: Seat, Frame Adapter-Set
[More]
|
|
Ford Mustang II;
Disc Brake Kit with Force 10 Elite 4-Piston Aluminum Calipers and 11" Rotors For GM & Ford Bolt Pattern (Front) - Disc brake
kit with Force 10 Elite 4-Piston Aluminum calipers and 11"
rotors for GM & Ford bolt pattern. Front steer.
Specifications: Minimum Wheel Size: 15" Caliper Name: Force 10 Elite
Number of Pistons: 4 Piston Size: 45mm Material: Aluminum Caliper
Standard Finish: Clear Anodized Caliper Optional Finished: Polished or Powder
Coated Rotor Diameter: 11 Rotor Thickness: 0.875" Rotor Venting: Uni-directional
(straight vane) Rotor Standard Finish: Slotted Rotor Optional Finishes: Plated
Bolt Pattern: 5 x 4.5" and 5 x 4.75"
Additional Features: All hardware included. Calipers come with clear
anodized finish. Optional polishing or powder-coating available. Includes Force
10 Elite 4-Piston aluminum calipers. Includes Ride Right 1.5"
drop spindles. Includes Turbo slotted rotors. Rotors available
with optional Xtra Life plating.
$1,885.00
2002-2005 Ford / 2002-2006 Lincoln:
Rear Power Slot Slotted Rotor
Left
[More]
|
Power Slot Toyota Celica Gts 2000 Power Slot Slotted Rotors; Front Rotors - Rotors Are Directional. Psl = Left Putco Chevy Silverado Heavy Duty 01-02 Putco Clamp-On No Drill Grille; Virtual Horizontal Grille (Grill Grilles Grills) 1976-1986 Jeep CJ-7;
Rear Drum To Disc Brake Conversion Kit For Amc 20 Axles with Warn Full Floating Hubs (Rear) Ryno Manufacturing
GM Fullsize Truck 85-06 Billet Accessories;
Blue Billet Pedal Kit "SCALLOP" Street Scene Ford F150 97-98 Bumper Covers/Valance; Front Bumper Cover/Valance 1996-1998 Honda Civic
Carbon Fiber Carbon Creations Rear Bumper Mercury Villager / Nissan Quest 99-00;
Headlight Cover (Small), Smoke
The Keith Green Collection
New Generation Ministries Christian Book Store Bargain Church Bibles Christian Rental FCS Family christian ...
Animals & Flowers
New Generation Ministries Christian Book Store Bargain Church Bibles Christian Rental FCS Family church ...
Live at the Woodlands
New Generation Ministries Christian Book Store Bargain Church Bibles Christian Rental FCS Family christian ...
|
|
NAME - DESCRIPTION |
|
